Phone ringtone generator circuit

This is a simple home telephone ringtone generator circuit which is built with applying only several electronic components / parts.It generates simulated telephone ringtone and requires only DC supply with 4.5V DC to 12V DC voltage.One may possibly use this circuit in ordinary intercom or phone-type intercom. 

The sound is pretty loud when this circuit is operated on +12V DC power supply. Even so, the volume of ring sound can be adjusted.

Read More

Phone Ring Generator Using Switching Supply

Phone Ring Generator Using Switching Supply Circuit

The telephone ring generator shown generates the bare aerial voltage from a simple switching approach ability accumulation (SMPS) which employs a CMOS Schmitt Trigger aboveboard beachcomber oscillator, 10 mH inductor, aerial voltage switching transistor (TIP47 or added aerial voltage, 1 amp transistor) and a disciplinarian transistor (2N3053). The inductor should accept a low DC attrition of 1.5 ohms or less. The switching accumulation charge accept a amount affiliated to anticipate the voltage from ascent too high, so a 22K resistor is acclimated beyond the achievement which banned the voltage to about 120 DC with the buzz ringer broken and about 90 volts DC connected. The achievement voltage can be adapted by alteration the amount of the 150K resistor amid pins 10 and 11 which will adapt the oscillator abundance (frequency is about 800 Hz as shown).

The accumulation is gated on and off by a additional Schmitt Trigger oscillator (pins 12/13) so that the buzz rings for about 2 abnormal and again the ambit idles for about a minute amid rings. These times can be adapted with the 10K and 300K resistors affiliated to pin 12. The advance button apparent is acclimated to manually arena the phone. The 25Hz campanology abundance is generated by addition Schmitt Trigger oscillator (pins 1/2) which controls the H arch transistor achievement circuit. The 6 transistors in the achievement date (4 NPN, 2 PNP) should be aerial voltage types rated at 200 volts beneficiary to emitter or more. The ringer will alone draw about 10 mA, so the achievement transistors can accept a low accepted appraisement but charge accept a aerial voltage rating. I acclimated TIP47s and baby arresting PNPs of alien numbers that I had on hand, but added types such as NTE287 (NPN) and NTE288 (PNP) should work. Both accept a 300 volt C-E appraisement and amount about $0.95 from mail adjustment houses.

The two 470 ohm resistors affiliated to the achievement serve to absolute the accepted in case the achievement is shorted. I never approved shorting the achievement to see how able the resistors are, but I did lose a brace transistors and again absitively to add the resistors. They should absolute the billow to about 120 mA which should be low abundant to anticipate damage. The ambit draws about 250 mA back the arena arresting is present so if you appetite to accomplish it from batteries, six D blazon acrid beef are recommended. It apparently wont assignment with a baby 9 volt battery.

Read More

Make A Virtual Phone Battery

Virtual cell phone battery is a replacement cell phone batteries for those of you who use the phone as a modem. Including myself, who use the phone as a modem HAIER d1200p internet.  Why must use this virtual battery. For those who surf hobby "full time" with a phone modem, would know the problem, the battery gets hot and fast reply wasteful even worn out.

This tool is a good solution to keep and care for our cell phones from the possibility of damage from over-charging its battery. I created a virtual battery works as follows: We take the source of its power supply from the USB port because the port is very easy and simple to use and simply provide a standard current source when the phone is online (500-750mA).

The workings of the circuit is as follows: Diodes or diode 2Amper in 5239 this standard to provide a useful addition to the polarity of the voltage which is also a component of protection against misuse. You can just use a 1 Amp diode (IN4002-4007). I use the IN 5239 is due to be durable, more resistant to heat. 4v3 zener diode IN4007 and configured to create a portal voltage of 5V (4.3 + 0.7 volt zener Vin4007) and is useful as a protection system against possible voltage spikes in the event of damage to the CPU. 220nF capacitor as a stabilizer and a substitute for the original battery cells.

The following also 100pF capacitor to smooth and filter the dc current through the diode 5239 which came out of the induction logging. Configuration between zener4v3, IN4007 diode and C 220n form a cell replacement from the actual battery cells, because the battery was actually a capacitor which had a large capacity. You can just remove the three components mentioned above. although it can work fine .

But results are not as good as that use virtual cell (replacement), which certainly was the security which we have to think to avoid the things which are not in want. Making way is to use an old cell phone batteries which have been wasting his cell, a raft of this circuit and the solder terminals on the batteries with the polarity distinguished. Make two holes for the cable to the jack / USB jack.

 Determine the length of cable required to taste and use stranded cable with a diameter of at least 1mm. If some type of cell phone batteries are very thin, use a small box for this circuit and connect the two wires to the output voltage again for hp battery casing. Or also if you do not have a former battery casing, use alligator clips to the battery terminal on the phone .. Pin the middle of the virtual pin replacement battery is BSI (Battery Size Insdicator) is useful for HP Nokia.

Read More

Circuit diagram Detector Cell phone

Detector Cell phone circuit diagram

This cellular buzz detector schematic ambit can faculty the attendance of an activated adaptable corpuscle buzz from a ambit of one and-a-half meters. If a RF arresting is detected the ambit will acquaint you application a complete anxiety (beep complete ) and a blinking LED .

In this blazon of ambit (that use aerial abundance 0.9-3Ghz ) you can not use an LC ambit for abundance affability .The ambit uses a 0.22μF deejay capacitor (C3) to according the RF ambit to ensure the adequacy of the ambit to abduction the adaptable buzz arresting .

This cellular buzz detector can ascertain any action of a adaptable buzz : admission or approachable SMS , video manual or articulation manual . The C3 capacitor charge accept leads breadth of 18 mm with 8 mm agreement amid leads to access the adapted abundance . This baby deejay capacitor acts as a baby gigahertz bend antenna to aggregate the RF signals .

The CA3130 operational amplifier IC is acclimated as a accepted to voltage advocate .This cellular buzz detector cyberbanking ambit diagram can be acclimated to verify the attendance of an alive cellular buzz in the activated breadth .

Read More

Make your phone battery last longer

 

Running out of battery at the most inconvenient moment is a situation that happens more often than we would like. The services currently offered multiple cell phones lead to a continuous drain on the battery, having often upload at the end of the day as if our smartphone need rest as much as us. To try to make the battery last us a bit more, we offer these tips:

1. The screen is ample, which consumes more energy on our phone. Therefore, avoid looking at every minute cell would be to start with the best advice. Adjust the screen brightness will also help us better power consumption. Likewise, it is advisable to reduce the consumption of games, watch videos, or even record and take pictures. All these applications have a high battery consumption, and if what we want is that last a little longer, we have to reduce the time spent on these activities.

2. Any service to determine our location, such as GPS, it should be disabled if not in use at that time. There are many services that use location for information about us and if we do not need, we will inadvertently limiting the life of our battery.

3. Optimize battery usage. Some phones include software specifically designed to optimize battery usage, so its a choice you make. If our model integrates not, we can always unburden an app to perform that function. There are many for all operating systems.

4. Having automatic updates enabled our favorite social networks, emails or any other tool, it will not help either. Because of the frequency with which updates are received, this is an unnecessary battery drain. Ideally disable this feature and manually check the applications when we agree.

5. Whenever we are in our home, at work, or have available a Wi-Fi, it is advisable to disconnect the data service and connect to the wi-fi. Our battery will thank us.

6. When we are connected to a wi-fi, we must use to update your operating system and various applications. Although it can be a bit cumbersome, especially OS upgrade, our phone will work more efficiently, as we most likely will include some improvement on the energy use of our device.

7. Heat is a great enemy of electronic devices. Avoid, as far as possible, the phone is exposed to extreme temperatures, especially heat, as it affects the life of the battery.

8. Finally, using these tricks even if you still have the feeling that your battery lasts very little, you can always buy an external battery that lets you use the phone a little longer.

Read More