Showing posts with label leds. Show all posts
Showing posts with label leds. Show all posts

Tuesday, November 4, 2014

Dicing With LEDs

Every self-respecting DIYer makes his own electronic dice with LEDs as spots. Then you don’t have to throw the dice anymore – just push the button. The electronics also ensures that nobody can try to improve his luck by fiddling with the dice. Too bad for sore losers! This circuit proves that an electronic die built using standard components can be made quite compact. The key component of here is a type 4060 digital counter (IC1). This IC has an integrated oscillator stage, so only two resistors (R7 and R8) and a capacitor (C7) are necessary to generate the clock signal. The clock signal is divided by various factors by the internal digital circuitry of the IC.

The division factors are designated by ‘CT’ in the IC drawing symbol. For instance, the signal on the CT3 output (pin 7) is a square wave with a frequency equal to the clock frequency divided by 23 (8). The clock signal is divided by 24 (16) on the CT4 output, by 25 (32) on the CT5 output, and so on. This means the output signals form a binary number that Dicing with LEDs counts upwards, which is naturally what a counter does.Of course, a die has only six possible values marked on the six sides of a cube. This means that at least three bits (the first three outputs) of the counter are necessary to drive a display. Eight different counter states (23) can be represented with three bits, but in this case the counter must be restricted to six states.

Dicing With LEDs Circuit Diagram

dicing-with-led-circuit
dicing-with-led-schematic-circuit

To make sure this happens, D11, D12 and R6 are used to reset the counter to its initial state when it reaches the seventh state, which means when it reaches a binary count of 110. When this happens, pins 4 and 5 of the IC are both logic ‘1’ (high level), which causes a logic ‘1’ to be applied to pin 12 via resistor R6. This causes the counter to be reset, which is what we want. The display consists of seven LEDs arranged in the same pattern as the usual markings on a normal die. 

This arrangement is shown in the schematic diagram. Before you begin thinking about the proper logical connections between the LEDs and the counter outputs, you can start by noting that except for the ‘1’ state there will always be two LEDs lit up at the same time. This means that only four distinct indications are necessary, instead of seven (with a total of seven LEDs).Another advantage of this is that the current consumption can be reduced by connecting pairs of LEDs in series. Resistors R1–R4 limit the current through the LEDs to approximately 2 mA. This means you have to use low-current LEDs. They are nice and bright at a current of 2 mA. Resistor R3 has a higher value because only one LED is driven via it.

For convenience, the circuit is dimensioned based on using a 9-V battery. The current consumption of the circuit depends on the number of LEDs that are illuminated, and with our prototype it varied over a range of approximately 2.5 mA to 6.5 mA. The LEDs still produce enough light even when the supply voltage is as low as 6 V, but this depends strongly on the characteristics of the low-current LEDs used in the circuit. Diodes D8–D10 and transistor T1 are necessary to enable all the states of a normal die to be shown. By that, we primarily mean the states with two or three spots, which must be located diagonally. For readers who want to delve more deeply into the design, the following table shows the six different binary states, which LEDs are lit up for each state, and the number of spots shown by the die.

The die is operated by switch S1. In the quiescent state, the break contact of S1 is closed and the oscillator is stopped because the input of the oscillator stage is connected to ground via the switch. When S1 is pressed, the oscillator starts running and causes the states of the LEDs to change at a rate of 1 kHz, which is too fast to follow with the naked eye. This high frequency ensures that the state of the die is purely random when S1 is released, so there is no regularity or pattern in the results. The circuit can be assembled on a small piece of perforated prototyping board. Fit the LEDs in exactly the same pattern as shown in the schematic diagram, since otherwise the spot patterns will not correspond to a real die. When you have assembled the circuit board, fit it in a plastic enclosure along with a 9-V battery to provide power.


Read More

Tuesday, October 28, 2014

NE555 Flashing LEDs

This Flashing LEDs uses a clean Astable multivibrator built around the general timer IC NE555. Resistors R1,R2 and capacitor C1 determines the output frequency. what time the output becomes excessive, Red LEDs light basic. When the capacitor C3 charges fully, Yellow LEDs light. The delay occasion relating this depends on the denomination of C3. while the output of Astable turns low leafy LEDs light using the current stored here the capacitor. Since this cycle is very fast, several levels of Flashing can come to pass obtained. If the light from Green LEDs is low, reduce the numeral to lone.

NE555
NE555 Flashing LEDs Schematic

Read More

Saturday, August 30, 2014

High Power LEDs up to 15 Amperes Wiring diagram Schematic

This High Power LEDs up to 15 Amperes Circuit Diagram employs a simple scheme that limits the current flow to the LED, you can easily modify the schema, and can change the power just replacing the value of R2. You can use a DC source of any tensions between 9V to 15V.Para powers or other LEDs just use the approximate formula:

Current (I) = 0.8/R2 where I is the current specified by the LED manufacturer. Value of I this conductor is 10A. Use R2 = 0.8/Current formula (I) to determine R2.

High Power LEDs up to 15 Amperes Circuit Diagram

High


Parts List

Q1 2N3055 or similar NPN transistor
R1 1W 220ohms
D1, D2 1N4001 silicon diode or rectifier

See R2 power for each LED

R2 for 1W LED 1W 2.7ohms
R2 LED to 1.5 ohms 1W 3W
5W LED R2 to 0.6 ohms or 2 x parallel 1.2-ohms/1W
Read More